I know, right? It’s so hard to “really” mess something up and Toolboxes are very cool for things not served by Flatpaks or Overlays.
I know, right? It’s so hard to “really” mess something up and Toolboxes are very cool for things not served by Flatpaks or Overlays.
Regarding your not wanting to go with an immutable distro: what configs are you thinking you’ll need to mess with that makes an immutable distro a bad idea exactly? I was previously on the fence about it as well but Bazzite has absolutely served my needs and requires way less fiddling than my previous Nobara install did after major updates. I have yet to find any day to day configurations that I haven’t been able to overcome with OSTree overlaying. Aside from being immutable, Bazzite literally checks every other box you’ve got listed.
Isn’t AMD’s HEVC/265 still decent, specifically? I feel like I read that somewhere years back. 264 has always been a weak spot for them, however.
Atomic OS’s (especially Fedora based) with Nvidia are going to be a bit of a pain. Did you follow all the instructions found Here ? I personally gave up on silverblue/kinoite after I tried Bazzite. Similar bases, but the Bazzite devs paid special attention to GPU and accessory drivers/implementations that are otherwise much more painful in Fedora Atomics. You can always do a clean rebase then re-run the steps above (only the OSTree section).
Software-wise, it seems that the relatively fast adoption of flatpaks and other containerized formats somewhat solves the typical dependency hell that was so common in Linux just a few years back (and to some extent still is an issue today depending on your distro and use case). The hardware support side is a little harder. That’s going to be up to vendors to play nice with the Kernel team and/or introduce reasonable userland software that doesn’t break the golden rule. Until Linux gets more market share the latter isn’t likely to happen. A nice side benefit of the emergence of immutable and/or atomic distros is that users can play around and try things with much lower risk of bricking their systems, so I’d also consider that a step closer in the “it just works” department.
Xbox controllers (Xbox One and newer) have been absolutely solid for me with the xone driver + xpadneo, regardless of distro. Bazzite has everything I need baked in, so it was completely plug and play. Not a very interesting answer, I know. But it still blows me away that it “just works.”
Very true. But brute force checking through tons of different settings for each camera you need to configure is not fun. I couldn’t seem to find any kind of “known working configs” database or anything either. Every camera seems to be different in what it expects, outputs, authenticates, etc. Once it’s set up, I agree, maintaining the config is easier. Having all your cameras match in model and firmware version probably makes the whole endeavor MUCH easier.
AmCrest and Frigate together are SO good. Integrating Frigate with Home Assistant was also insanely easy for quick viewing and notifications. That initial Frigate config is a bit of a bear- but once you’re past that I cannot speak more highly of it.
hunter2
I’ve had good luck with AsRock as well. Before this most recent generation I was Sapphire all the way. But they charge a good premium now that I don’t feel is worthwhile if you’re in the ~7600xt range or lower.
Even with nvme drives which supposedly “don’t need” to use BFQ, I STILL always swap it since it maintains responsiveness across the system during heavy IO loads. I used to have similar full system freezes when downloading steam games which notoriously overload your IO in Linux. BFQ was the solution every single time.
Edit Try following the instructions detailed in this post to add a systemd rule to set the scheduler: https://stackoverflow.com/questions/1009577/selecting-a-linux-i-o-scheduler
The second answer that shows an actual rules.d file example has always worked for me. If using nvme or old school spinning rust you’ll need to change it up a bit. Instead of “noop” set it to “BFQ”.
Try swapping to BFQ io scheduler and see if that makes a difference.
I’m going to assume it’s not Universal Blue… But parts of your description reminded me of it.
I have personal experience with BTRFS and Windows. And that experience is that it’s roughly as stable/complete as NTFS is for Linux. 6 of one and a half dozen the other. I can’t recommend either situation for guaranteed stability long term between systems if one really needs to swap between the OS’s frequently while accessing all the same files.
I run mine with the actual photos on HDD but the database on SSD. So far everything has been near instantaneous for loading, downloading, uploading, you name it.
I can vouch for Bazzite. Been running it on my desktop and laptop (both amd gpu’s) with virtually no issues or hiccups. The desktop is even dual boot, despite that not being advised.
The Truecharts version of Qbittorrent has gluetun baked in as an option already. Initial configuration can be a bit of a pain depending on your VPN provider, but it seems to work beautifully once set up.
Maybe not too helpful, but could point you in the right direction: you used to be able to use “gksudo” to get the graphical popup requesting your password in lieu of sudo which would only ask for a password in terminal. I believe gksudo is deprecated/non-existent at this point but there’s got to be an alternative out there. Best of luck!
Adding repos can just be done inside a Toolbox, or even as Overlays. Grub can also be edited and changes applied to immutable OS’s like Bazzite/Kinoite. I’d definitely say give it a shot on a non-daily driver machine and see how you like it. Having the option to mess with the underpinnings can be nice- but not having to has a lot of value as well.